×

Our Products

BENZi Hi-Heat 600

Heat Resisting Silicone Aluminium Paint

Share With:

  Paint Calculator
BENZi HI-HEAT 600 is a heat resisting silicone aluminium paint specially formulated to withstand continuous temperature up to 600°C and pigmented with aluminium flakes which gives excellent anti-corrosion protection for interior and exterior ferrous metal surfaces which exposed to extreme temperature. Ideal for use on furnace, chimney, exhaust, boiler, oven, machinery and engine room.

 
Painting System:
Substrate
Primer  ( 1 coat )
Intermediate  ( 1 coat )
Topcoat  ( 1 coat )
New Ferrous Metal 
(For optimum performance)
BENZIPOX Hi-Heat Primer or Inorganic Zinc Rich Primer
BENZi Hi-Heat 600
BENZi Hi-Heat 600
New Ferrous Metal 
BENZi Hi-Heat 600
BENZi Hi-Heat 600
BENZi Hi-Heat 600
Previously Painted Ferrous Metal 
BENZi Hi-Heat 600
BENZi Hi-Heat 600
BENZi Hi-Heat 600

5 litres & 15 litres

Surface Preparation

New Ferrous Metal
Surface generally must be clean, free from rust, oil, grease, dust and other contaminants and must be thoroughly dried before application. Steel surface shall be manually wire brush or power tool cleaning to remove all rust or loose millscale as to comply with minimum Swedish Standard ST 3, then primed with appropriate primer / intermediate coat before application of topcoat. 

Previously Painted Ferrous Metal
Previously painted surface should be thoroughly rubbed down using a suitable abrasive paper and then dusted off. Any loose and flaking paint film must be scraped off, rust should be thoroughly removed (for optimum performance, wire brush or power tool cleaning to a minimum Swedish Standard ST 3 is highly recommended). The entire surface must be dry and free from dust, grease and other contaminants, spot-primed any surface imperfection with appropriate primer / intermediate coat before application of topcoat.
 

Environmental Conditions During Application

Do not apply BENZi Hi-Heat 600 when the relative humidity exceeds 85% or when the surface to be painted is less than 3°C above dew point; Do not apply at temperature below 7°C, otherwise drying and overcoating times will be considerably extended; This product will only be fully cured upon exposure to temperature @ 200°C for minimum 5 hours and must not be exposed to temperature above 600°C during this period. 

 
Color :  Aluminium, refer BENZi High Performance Coating color card
Film Finish :  Metallic lustre Low Gloss
Touch Dry :  1 hour (depends on temperature and humidity)
Recoating Interval :  Minimum 10 hours
Solid Content :  45% (by weight); 30% (by volume)
Dry Film Tickness :  20 - 30 microns / coat
Theoretical Coverage :  10 - 15 m2 / liter / coat (actual coverage is dependent on loss factors)
No. of Coat :  Minimum 2 coats
Application :  Brush, roller or air spray
Thinning :  Ready for use after thorough stirring, dilute up to 5% of Thinner if necessary
Cleaning Up :  Clean all paint equipment with Thinner immediately after use

 

Safety, Health & Environment

FLAMMABLE. During painting, make sure no source of ignition at surrounding and no smoking. When not in use, store paint in cool and shaded place and do not directly expose to sunlight. Allow proper ventilation and wear mask during painting. Do not breathe vapour or spray. Keep doors and windows open during application and drying. It is advisable to wear eye protector while applying. In case of contact with eyes, rinse immediately with plenty of water and seek medical treatment. To remove splashes of paint from skin, use suitable cleanser or soap and water. Do not dispose paint into drains or watercourses. Refer to MCI Paint Technical Data Sheet (TDS) for further details. 

Materials Safety Data Sheet (MSDS) is available upon request.

Click link below to download
Technical Data Sheet (TDS)

Click link below to download
BENZi High Performance Coating

Related Products

SUBSCRIBE TO NEWSLETTER