BENZITOP ATC 200

Our Products

Home
/
Our Products
/
BENZITOP ATC 200

BENZITOP ATC 200

Synthetic Solvent Based Acrylic Finish

Share With:

Paint Calculator

BENZITOP ATC 200 is a one pack solvent based fast drying acrylic high sheen finish with excellent weather resistance and hardness to provide durable performance against harsh weather condition. It can be applied over properly primed masonry, metal and wood surfaces for both exterior and interior use. Recommended to be used as a topcoat for multi-layer decorative and protective coating system such as textured painting system, repainting of metal roofing, cladding and concrete roof tiles.

General Properties: Does not chalk easily despite exposure to UV light; Resistant to splash and spillage of large variety of dilute acids, alkalis, detergents, petroleum products, mineral and vegetable oils; Superlative gloss and colour retention on outdoor exposure; High stain resistance and impact resistance; Fungus resistance as to prevent unsightly growth of surface fungus on painted substrate.

Painting System:
Substrate	Primer / Sealer (1 coat)	Intermediate (1 coat)	Topcoat (1 - 2 coats)
Wood	BENZi Aluminium Paint	BLUE-i Undercoat	BENZITOP ATC 200
Ferrous Metal	BENZi Zinc Phosphate Primer or BENZi Red Oxide Primer	BLUE-i Undercoat	BENZITOP ATC 200
Non-Ferrous Metal	BENZi 100 Etching Primer or BENZIPOX EA9 Red Oxide Primer	BLUE-i Undercoat	BENZITOP ATC 200
Masonry Wall	BAOMA Excila 1900	BENZITOP ATC 200	BENZITOP ATC 200
Masonry Wall (Textured Painting System)	BAOMA Excila 1900	BLUE-i Versa-Tile	BENZITOP ATC 200

5 litres

Surface Preparation

New Ferrous Metal / Wood Surface
Surface generally must be clean, free from rust, oil, grease, dust and other contaminants and must be thoroughly dried before application. Steel surface shall be manually wire brush or power tool cleaning to remove all rust or loose millscale as to comply with minimum Swedish Standard ST 3, then primed with appropriate anti-corrosion primer follow by undercoat before application of topcoat. Wood surface shall be sand down to smoothen the surface, then primed with aluminium wood primer follow by undercoat before application of topcoat.

Previously Painted Ferrous Metal / Wood Surface
Previously painted surface should be thoroughly rubbed down using a suitable abrasive paper and then dusted off. Any loose and flaking paint film must be scraped off, rust should be thoroughly removed. The entire surface must be dry and free from dust, grease and other contaminants, spot-primed any surface imperfection with appropriate primer / undercoat before application of topcoat.

Non-Ferrous Metal Surface
For new surface, thorough solvent degreasing to SSPC-SP1 is necessary. For old surface, it must be abraded to remove corrosion deposits. All surfaces must be dry and clean prior to painting.

Masonry Surface
Ensure the surface to be painted is clean, dry and free from dirt, oil, grease and other contaminants. Remove all loose or powdery residues by brushing or scraping with a stiff fibre brush under running water or by using high pressure water jet. Areas affected by mould, lichen, algae or fungus must be treated with MCI Micro Kill. Repair defects with a suitable filler or putty. Apply BAOMA Excila 1900 where high alkalinity is present. Avoid painting where surface is high in moisture content or during wet weather (recommended painting specification requires moisture content of the wall to be below 16% as measured by protimeter and alkalinity of the wall below pH9).

Binder	: Synthetic Acrylic
Finish	: High Sheen
Color	: Assorted colors, refer Color Infinity & BENZi High Performance Coating color card
Thinner	: Thinner
Solid Content	: 45% (by weight); 34% (by volume)
Dry Film Thickness	: 25 - 30 microns / coat
Theoretical Coverage	: 11 - 13 m² / litre / coat (actual coverage is dependent on loss factors)
No. of Coat	: Minimum 2 coats
Touch Dry @ 30°C	: 30 minutes (depends on temperature and humidity)
Recoating Interval	: Minimum 4 hours
Shelf Life	: Minimum 12 months if properly stored

Safety, Health & Environment

FLAMMABLE. During painting, make sure no source of ignition at surrounding and no smoking. When not in use, store paint in cool and shaded place and do not directly expose to sunlight. Allow proper ventilation and wear mask during painting. Do not breathe vapour or spray. Keep doors and windows open during application and drying. It is advisable to wear eye protector while applying. In case of contact with eyes, rinse immediately with plenty of water and seek medical treatment. To remove splashes of paint from skin, use suitable cleanser or soap and water. Do not dispose paint into drains or watercourses. Refer to MCI Paint Technical Data Sheet (TDS) for further details.

Materials Safety Data Sheet (MSDS) is available upon request.